Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Discussion > Honda Technical

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 07 Sep 2007, 02:36 pm
Member
 
Join Date: Sep 2007
Posts: 49
Default I've been working on a 95 honda civicEX. Can I put a crankshaft pulley from a DX into an EX?

Will it drive ok? The crankshaft pulley for the DX (part # 13811 p00 u00) weighs less than the crankshaft pulley for the EX (part # 13810 p26 003)...But I think the belts will still fit on if I do install the DX crankshaft into my 95 2DR Automatic Trans Civic. I really just need to know what difference it will make this DX crankshaft is installed into my EX.Thanks!!!
Reply With Quote
  #2 (permalink)  
Old 07 Sep 2007, 02:39 pm
Junior Member
 
Join Date: Sep 2007
Posts: 15
Default

if its a different engine then i wouldn't be swapping parts between the 2 if its the same engine then go for it have fun.
Reply With Quote
  #3 (permalink)  
Old 07 Sep 2007, 02:42 pm
Senior Member
 
Join Date: Aug 2007
Posts: 285
Default

i own a repair shop,and what you need to do is compare the part numbers on it,Honda's are good for putting numbers on everything, i think they will interchange ,but look at the part numbers just to be sure,and if the will it should be ok on it,if all the marks line up then the timing marks should be the same also,but make sure before you install it on there,good luck i hope this help,s.PS the only difference it might make is you might get a little shake out of it,and if it does this you cant use it.
Reply With Quote
  #4 (permalink)  
Old 07 Sep 2007, 02:46 pm
Junior Member
 
Join Date: Sep 2007
Posts: 2
Default

As long as the pulley diameter and bolt holes match it should be ok. BTW remember to see if the belt grooves match too. If everything matches then it ok.
Reply With Quote
  #5 (permalink)  
Old 07 Sep 2007, 02:48 pm
Junior Member
 
Join Date: Sep 2007
Posts: 14
Default

The weight savings would actually be a good thing, but why is it lighter? Does it not have as many slots for belts, seeing how most DX's have less accessories. If there is enough room for the belts, you can swap them over.
Reply With Quote
  #6 (permalink)  
Old 07 Sep 2007, 03:00 pm
Junior Member
 
Join Date: Sep 2007
Posts: 6
Default

i dont think so because the ex in a vtech engine and the dx is not. most parts on these engines can be swapped becaus ethey are all alike except some of the vtech engines.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
How do you find TDC on a Honda Civic D15B7 with the crankshaft pulley attached? james Honda Technical 8 03 Sep 2007 03:44 pm
Crankshaft pulley turns but not cam punkyw Honda 3 6 15 May 2005 02:04 am
Honda Crankshaft pulley falls off jjeansonne Honda 3 6 27 Feb 2005 11:04 pm
Chipped Crankshaft Pulley Caroline Honda 2 44 01 Jul 2004 11:37 pm
Chipped Crankshaft Pulley Caroline Honda 3 26 01 Jul 2004 11:37 pm


All times are GMT -5. The time now is 05:37 am.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.