Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Discussion > Honda Technical

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 01 Nov 2011, 05:45 pm
Junior Member
 
Join Date: Nov 2011
Posts: 1
Default D15B7 obd1 dizzy onto D15B2 obd0

Quick run down of what happened. First off the block is a JDM D15B, although as far as I know those are supposed to be vtec but that's not the case with this motor. Aside from the D15B stamped on the block it looks to be a typical dpfi D15B2 head. Bearing inside the dizzy started to go, and me being too lazy to do anything about it I waited until the ecu jumped into limp home mode since the sensors inside got chewed up because the bearing had wore out so bad that the shaft started running on an angle. Mainly the crank position sensor got damaged the most which is what code I'm getting off the ECU. The dizzy cap had the contacts nearly sliced off. I couldn't believe the motor was still running to be honest.

Friend of mine gave me a spare dizzy he had off of a D15B7, at least I think that's what it is. I forgot to ask when I got it, but it was a 94 either cx or dx, but I think dx because the motor was 16 valve. Doesn't matter. Wiring should be the same.

So I wired it up. Simple enough. Just want to double check the wiring with you guys since I just used mitchell to put it together.

tdc [obd0]wht-blu [obd1]wht-blu
tdc [obd0]org-blu [obd1]org-blu

ckp [obd0]wht [obd1]lt-blu
ckp [obd0]org [obd1]blu-yel

ignition input signal [obd0]wht [obd1]yel-grn

--------- [obd0]blk-yel [obd1]blk-yel
tach [obd0]blu [obd1]blu


I left the org and wht wires from the CYP alone since this is a dpfi and the old dizzy didn't have them either so I'm guessing that's okay. One thing I wasn't sure about was in which order the 2 wires from each sensor go with the wires on the harness. ie: ckp wht goes with lt-blu or blu-yel. I figured I got it right with the tdc because I'm not getting any codes. But I'm getting a code about the ckp sensor.

The wiring diagrams for the D15B2 show each wire coming off the ckp sensor going into pins on the ecu that are both labeled as CKP input. I kind of thought that one should be an output and the other an input. On the wiring diagram for the D15B7 it shows 'ckp p' on one ecu pin and 'ckp m' on the other. Don't know what the p or m stand for. Thought positive and minus for a sec but figured it would make more sense to use n for negative in that case.

I tired swapping the wires around to see if it'd make a difference, but nothing. I reset the ecu, code is gone up until I start the motor, and then its back right away. I checked resistance, shorts to ground, continuity, everything seems good. Just in case, I had a spare PM5 ecu (was currently running a PM9) and same thing. Code 4. And as far as I know this dizzy came off of a running motor with no codes at the time. I guess it is possible that I got screwed with a dizzy that has another bad ckp, but I thought I'd ask here before I go looking for another one.

Oh, and the last thing I tried before giving up for the day was flipping around the nose that goes into the camshaft. Having it set the original way that it comes out of the D15B7, the timing ends up being 180 degrees off on the D15B2 head. Not a big deal I thought since its a dpfi and doesn't need to know which cylinder is #1 so I just put the #1 plug wire where it would usually be the #4 wire. But after all the trouble I was having, I flipped the nose so the #1 wire was in the same spot as it would be on the D15B7.

The only other thing I thought about doing but was kind of hesitant was to splice in 2 fresh wires straight from the ecu to the dizzy just in case there's something strange in the wires that's causing the ecu to throw out the code.
Other than that, I don't know. Any help would be appreciated.

Actually some good info would be to know exactly how these sensors work. Is there a voltage signal of some sort sent and the returned to the ecu when the reluctor passes the contact point. I mean I find it stupid that the only test mitchell or the civic service manual gives is to check ohms and wires and that alone determines whether the sensor or ecu are screwed. They even suggest replacement of the distributor assembly instead of just changing out the sensor.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
honda/acura OBD0 TO OBD1 engine harness? jacob m Acura Technical 1 12 May 2011 02:16 pm
mini me swap in 89 civic, OBD1 wiring harness, stock d15 block, 97 Y8 head, OBD2 dizzy with... i_am_a_dude_2005 Honda Technical 2 14 Feb 2009 05:01 pm
i have a OBD0 integra and just got a OBD1 integra motor, what all do i need to swap it? Eddie S Acura Technical 5 20 Aug 2007 08:00 am
D15B7 HEAD ON D15B2 BLOCK DD Honda 2 8 09 Oct 2005 01:28 pm
electrical schedule D15B2 & D15B7 hondaman Honda 2 0 30 Dec 2004 01:09 pm


All times are GMT -5. The time now is 01:20 am.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.