Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Honda Acura > Honda 2

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 13 May 2009, 12:18 pm
lelec
Guest
 
Posts: n/a
Default Hot wheel, brakes or bearing ? (CR-V 2003)

Hi.

Car - Honda CR-V 2.0, 2003 y, 155 000 km.

Since i changed brake blocks, right rear wheel becomes quite hot after
few kilometers trips.

Before brake blocks change there was some occurrences, when this wheel
was hot, but rather rarely (when i forgot about hand-brake ).

There is not loud noise, when car going slow, but i dont konw, if it
is brake disc or bearing ?
How to check, if it is poor bearing or wrong brake blocks? Is there
other posibility?


Respect
--
Marcin
CR-V 2.0 2003
Reply With Quote
  #2 (permalink)  
Old 13 May 2009, 08:33 pm
Eternal Searcher
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

lelec wrote:

> Hi.
>
> Car - Honda CR-V 2.0, 2003 y, 155 000 km.
>
> Since i changed brake blocks, right rear wheel becomes quite hot after
> few kilometers trips.
>
> Before brake blocks change there was some occurrences, when this wheel
> was hot, but rather rarely (when i forgot about hand-brake ).
>
> There is not loud noise, when car going slow, but i dont konw, if it
> is brake disc or bearing ?
> How to check, if it is poor bearing or wrong brake blocks? Is there
> other posibility?
>
> Respect


Sounds like a seized brake caliper.
Reply With Quote
  #3 (permalink)  
Old 14 May 2009, 02:01 pm
Iowna Uass
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

You roasted a bearing.
I had the same issue with my 2005 CRV.
The caliper siezed last winter (2007/8) and I didn't notice until my spring
check (my bad)
I replaced the shoes and adopted an annual "brake lube" as part of my spring
inspection, however I noticed a rumbling coming from the rear of the
vehicle. I suspected a bearing issue.
Since my CRV was still under warranty, I took it in and they confirmed my
suspicions.
The wheel bearing on the siezed side was bad and they replaced it under
warranty.


Reply With Quote
  #4 (permalink)  
Old 14 May 2009, 06:55 pm
Tegger
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

lelec <marcin.pawelec@gmail.com> wrote in news:e24c7269-822d-4c17-938f-
9fd0b88c9b99@n4g2000vba.googlegroups.com:

> Hi.
>
> Car - Honda CR-V 2.0, 2003 y, 155 000 km.
>
> Since i changed brake blocks, right rear wheel becomes quite hot after
> few kilometers trips.
>
> Before brake blocks change there was some occurrences, when this wheel
> was hot, but rather rarely (when i forgot about hand-brake ).
>
> There is not loud noise, when car going slow, but i dont konw, if it
> is brake disc or bearing ?
> How to check, if it is poor bearing or wrong brake blocks? Is there
> other posibility?
>



Did you turn the piston back in before putting the new pads on?


--
Tegger

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
Reply With Quote
  #5 (permalink)  
Old 15 May 2009, 06:41 am
lelec
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

On 15 Maj, 01:55, Tegger <inva...@invalid.inv> wrote:
> lelec <marcin.pawe...@gmail.com> wrote in news:e24c7269-822d-4c17-938f-
> 9fd0b88c9...@n4g2000vba.googlegroups.com:
>
> > Hi.

>
> > Car - Honda CR-V 2.0, 2003 y, 155 000 km.

>
> > Since i changed brake blocks, right rear wheel becomes quite hot after
> > few kilometers trips.

>
> > Before brake blocks change there was some occurrences, when this wheel
> > was hot, but rather rarely (when i forgot about hand-brake ).

>
> > There is not loud noise, when car going slow, but i dont konw, if it
> > is brake disc or bearing ?
> > How to check, if it is poor bearing or wrong brake blocks? Is there
> > other posibility?

>
> Did you turn the piston back in before putting the new pads on?
>


Yes, i do,

Today i was at my friend, who has huge jack.
We take off both rear wheels, and check brakes: pads adheres to brake
disc. Bearings are ok, in my opinion.
What is the reason of this?

Should i replace brake caliper? or brake fluid? or brake pipes?


Respect
--
Marcin
CR-V 2.0 2003
Reply With Quote
  #6 (permalink)  
Old 15 May 2009, 07:42 am
Tegger
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

lelec <marcin.pawelec@gmail.com> wrote in news:caaa592d-7af5-4896-a9b3-
f42c6c5a9bf4@x6g2000vbg.googlegroups.com:

> On 15 Maj, 01:55, Tegger <inva...@invalid.inv> wrote:
>> lelec <marcin.pawe...@gmail.com> wrote in news:e24c7269-822d-4c17-938f-
>> 9fd0b88c9...@n4g2000vba.googlegroups.com:
>>
>> > Hi.

>>
>> > Car - Honda CR-V 2.0, 2003 y, 155 000 km.

>>
>> > Since i changed brake blocks, right rear wheel becomes quite hot after
>> > few kilometers trips.

>>
>> > Before brake blocks change there was some occurrences, when this wheel
>> > was hot, but rather rarely (when i forgot about hand-brake ).

>>
>> > There is not loud noise, when car going slow, but i dont konw, if it
>> > is brake disc or bearing ?
>> > How to check, if it is poor bearing or wrong brake blocks? Is there
>> > other posibility?

>>
>> Did you turn the piston back in before putting the new pads on?
>>

>
> Yes, i do,
>
> Today i was at my friend, who has huge jack.
> We take off both rear wheels, and check brakes: pads adheres to brake
> disc. Bearings are ok, in my opinion.
> What is the reason of this?
>
> Should i replace brake caliper? or brake fluid? or brake pipes?
>





Basically, your pads are dragging on the disc. It has nothing to do with
the bearings. It MAY have to do with a caliper hydraulic piston that is
seizing in its bore.

Honda's rear disc brakes can suffer from a number of issues that can cause
the assembly to overheat. I've seen everything from seized slide pins to
seized pads to seized pistons to seized parking brake mechanisms.

Replacing the fluid is never a bad idea (but may not help this situation),
but replacing the brake lines would be useless. You MAY need to replace the
calipers, but that depends on exactly what's wrong.

It would be better to let a professional look at your brakes. Or you can
read this:
<http://www.tegger.com/hondafaq/rustybrakes/brakes1.html>


--
Tegger

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
Reply With Quote
  #7 (permalink)  
Old 15 May 2009, 08:09 am
jim beam
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

Tegger wrote:
> lelec <marcin.pawelec@gmail.com> wrote in news:caaa592d-7af5-4896-a9b3-
> f42c6c5a9bf4@x6g2000vbg.googlegroups.com:
>
>> On 15 Maj, 01:55, Tegger <inva...@invalid.inv> wrote:
>>> lelec <marcin.pawe...@gmail.com> wrote in news:e24c7269-822d-4c17-938f-
>>> 9fd0b88c9...@n4g2000vba.googlegroups.com:
>>>
>>>> Hi.
>>>> Car - Honda CR-V 2.0, 2003 y, 155 000 km.
>>>> Since i changed brake blocks, right rear wheel becomes quite hot after
>>>> few kilometers trips.
>>>> Before brake blocks change there was some occurrences, when this wheel
>>>> was hot, but rather rarely (when i forgot about hand-brake ).
>>>> There is not loud noise, when car going slow, but i dont konw, if it
>>>> is brake disc or bearing ?
>>>> How to check, if it is poor bearing or wrong brake blocks? Is there
>>>> other posibility?
>>> Did you turn the piston back in before putting the new pads on?
>>>

>> Yes, i do,
>>
>> Today i was at my friend, who has huge jack.
>> We take off both rear wheels, and check brakes: pads adheres to brake
>> disc. Bearings are ok, in my opinion.
>> What is the reason of this?
>>
>> Should i replace brake caliper? or brake fluid? or brake pipes?
>>

>
>
>
>
> Basically, your pads are dragging on the disc. It has nothing to do with
> the bearings. It MAY have to do with a caliper hydraulic piston that is
> seizing in its bore.
>
> Honda's rear disc brakes can suffer from a number of issues that can cause
> the assembly to overheat. I've seen everything from seized slide pins to
> seized pads to seized pistons to seized parking brake mechanisms.
>
> Replacing the fluid is never a bad idea (but may not help this situation),
> but replacing the brake lines would be useless. You MAY need to replace the
> calipers, but that depends on exactly what's wrong.
>
> It would be better to let a professional look at your brakes. Or you can
> read this:
> <http://www.tegger.com/hondafaq/rustybrakes/brakes1.html>
>
>


it's also possible that there's a seized parking brake cable.

concur that it's unlikely a bearing and is more likely the caliper.
Reply With Quote
  #8 (permalink)  
Old 15 May 2009, 12:32 pm
Tegger
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

jim beam <me@privacy.net> wrote in
news:BLudnStfhOk99JDXnZ2dnUVZ_vqdnZ2d@speakeasy.ne t:


>>
>>

>
> it's also possible that there's a seized parking brake cable.




That too.



--
Tegger

The Unofficial Honda/Acura FAQ
www.tegger.com/hondafaq/
Reply With Quote
  #9 (permalink)  
Old 15 May 2009, 03:57 pm
lelec
Guest
 
Posts: n/a
Default Re: Hot wheel, brakes or bearing ? (CR-V 2003)

On 15 Maj, 19:32, Tegger <inva...@invalid.inv> wrote:
> jim beam <m...@privacy.net> wrote innews:BLudnStfhOk99JDXnZ2dnUVZ_vqdnZ2d@speakeasy. net:
>
>
>
> > it's also possible that there's a seized parking brake cable.

>
> That too.
>
> --
> Tegger
>
> The Unofficial Honda/Acura FAQwww.tegger.com/hondafaq/


I (really not I, but next mechanic!) found the reason!
New blocks was probably compatible with CR-V 2000, not 2003!
They have three protruding pointson it, that should be outside capiler
ring,
but one of them was in wrong place, and blocks were skrewed.
Mechanic gringed those points on gringer, and blocks fits perfect.
Now they adhere ideally.

They mixed up blocks in shop, an they probably sell wrong pair to me.

Thx for help.

Respect
--
Marcin
CR-V 2.0 2003
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
2003 Acura 1.7EL Wheel Bearing constant issue Aubrey Acura 4 20 Apr 2009 10:29 am
Front wheel bearing pelusa Honda Technical 0 29 Jan 2008 01:45 am
Brakes and Wheel Bearing? a_taste_of_ink Honda Technical 2 04 Sep 2007 04:33 pm
Rear wheel bearing won't come off Filipp Stepanov Acura 2 07 Jan 2005 11:12 pm
'98 TL Wheel Bearing?? MZ Acura 0 16 May 2004 01:06 pm


All times are GMT -5. The time now is 03:54 am.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.