Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Honda Acura > Honda 2

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 25 Jun 2006, 07:12 am
nospam
Guest
 
Posts: n/a
Default 90 Accord Tie Rod Ends Pt II

Before doing anything, check the front and rear suspension parts on both
sides and if they are really dirty, take the car to a car wash. Use some
good grease remover and clean both sides up really good.

In rebuilding the suspension on a 90-93 accord, it's best to do the lower
ball joints. Use an air wrench to take off the drive axle nut. It takes a
36mm socket, and it's put on with 78 ft pounds of torque, so you're going to
need some umph to get it off. Some of the detail removal is omitted here.
After removing the strut, use a puller and pop the steering tie rod end and
the upper control arm end. Don't unbolt them completely yet, just loosen
enough to pop them loose. Remove the brake stuff and hang the caliper. Now
pop the lower ball joint and remove the nuts on the steering tie rod end and
the upper control arm and the lower ball joint. You don't have to remove
the brake rotor (the bolts on the backing plate of ours have special star
heads, and we don't have a socket that fits), and be ready for some heavy
lifting on the steering knuckle. It comes out easy now. And you can take
the works to a parts house or machine shop for pressing out of the old and
in with the new. Or you can try pounding the old lower ball joint out. Be
sure you remove the lock ring first. We tried to knock the driver's side
out, and found that we couldn't get it all the way out because the little
guy in Japan who pressed in the hub bearing race when the car was built
didn't press it in quite far enough. It lacks maybe a 16th of an inch being
in far enough for the old ball joint to clear coming out.

Here's a rough list of some of the tools you will need to do this:

10, 12, 14, 17, 19, and 36mm wrenches and sockets, ratchets and pull handles
for 3/8 and 1/2 drives, floor jack, bottle jack, two jack stands, rubber
mallet, ball peen hammer, needle nose and regular pliers, spray lubricant,
brake cleaning spray, lug wrench, flat blade screwdriver or two, two-arm
puller, air wrench and compressor for the axle nut, factory service manual
or substitute, couple of 10" adjustable wrenches, torque wrench, a couple of
punches, lots of something cool to drink, a female companion to read the
manual for you so you don't have to get it greasy while working and to keep
you on track, and probably something else that I just can't think of right
off.

While you've got the brake stuff off, check the pads and make sure they
don't need to be replaced or the rotors turned because this is a golden
opportunity to do that.

Once you get the lower ball joints out and back in, now is the time to
replace all the other stuff with new, the upper control arm, the steering
tie rod end, the strut, the radius rod end, the stabilizer bar end and to
reinstall all the brake stuff.

Whew, what a job!!

dw


Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
90 Accord Tie Rod Ends Contd nospam Honda 2 0 03 Jul 2006 03:07 pm
90 Accord Tie Rod Ends Contd nospam Honda 2 1 02 Jul 2006 02:59 am
90 Accord Tie Rod Ends Contd nospam Honda 2 0 30 Jun 2006 05:08 am
90 Accord Tie Rod Ends Pt III nospam Honda 2 2 26 Jun 2006 08:45 am
90 Accord Tie Rod Ends nospam Honda 2 3 24 Jun 2006 08:39 am


All times are GMT -5. The time now is 02:37 pm.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.