Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Discussion > Acura Technical

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 02 Dec 2007, 09:31 pm
Junior Member
 
Join Date: Nov 2007
Posts: 8
Default does anybody know how to install MSD 6AL ignition box on an 1994 integra?

does anybody know how to install MSD 6AL ignition box on an 1994 integra?
Reply With Quote
  #2 (permalink)  
Old 02 Dec 2007, 09:46 pm
G T G T is offline
Junior Member
 
Join Date: Nov 2007
Posts: 18
Default

Go here; http://www.msdignition.com/pdf/6%20series/6series.pdf
Reply With Quote
  #3 (permalink)  
Old 02 Dec 2007, 10:01 pm
Junior Member
 
Join Date: Dec 2007
Posts: 5
Default

Should connect the same way I wired my MSD BTM... You will have to remove the 4 spark plug wires from the dist cap. Loosen 3 captive screws on dist cap. Remove dist cap. To remove the rotor you may have to crank the engine a split second at a time til the screw on the shaft of the rotor is facing the firewall... Remove the screw (use a magnetic tip screwdriver so it doesn't fall). Now you can remove the rotor and cover... You should see your factory coil with a - and + terminal. The two wires go strait to the Ignition Control Module... Cut the - wire in half, the MSD orange wire goes to the coil half and the MSD white wire goes to the ICM half... (you should use solder and shrink tubing)... Put a very small ring termnial on the MSD red wire and connect it to the + side of the coil terminal leave the original wire there too... Before doing this I forgot to mention that a 7/16 hole will need to be drilled in the dist cap and MSD wires will need to be routed through first. (upper part of the backside worked for me). The hardest part is fitting everything back together with the extra wires in the dist. Don't forget to find a good ground for the MSD black wire... You may also need a MSD tach adapter for your tach if it operates improperly or car fails to start after everything is back toghether and double checked... If your tach is operating improperly this may be worse than it sounds because your ecu uses the same rpm signals to calculate fuel to your engine... Good Luck...
Reply With Quote
  #4 (permalink)  
Old 02 Dec 2007, 10:16 pm
Senior Member
 
Join Date: Aug 2007
Posts: 101
Default

get a jumper harness. or just buy the sci ignition from msd, and it should plug right in.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
How much does it cost to install an ignition switch on a 1999 Honda Accord 4 cylinder LX? Kelfey L Honda Technical 2 21 Oct 2007 11:30 am
how to install a radiator in a 1994 honda civic ex? ed k Honda Technical 1 11 Oct 2007 11:24 am
How do you install an air intake system in a 1994 Honda Accord Ex? agustin Honda Technical 2 26 Sep 2007 06:36 am
how do i know if my ignition coil is bad on my 1994 integra rs? macho4486 Acura Technical 3 17 Aug 2007 02:54 pm
1994 Honda Civic- Ignition lock dtrejo Honda 3 2 15 May 2005 09:36 am


All times are GMT -5. The time now is 11:45 am.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.