Honda Car Forum


 

Go Back   Honda Car Forum - Accord Parts Civic Tuning Acura Racing > Discussion > Acura Technical

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 26 Nov 2007, 05:46 pm
Junior Member
 
Join Date: Nov 2007
Posts: 7
Default honda civic vti 99 b16, looking for answers about after market inlet manifold and

throttle body queries??????? hi i have purchased an aftermarket inlet manifold and i now have a skunk2 66mm throttle body i was going to port match the im with the throttle body!! but i am not sure how it will run with the bigger bore!! will i need to remap for the car to run or will it run without remap? i also have these parts to fit >>>>>aem fuel pressure reg>>>>>>>aem fuel rail>>>>>>>>aem fuel filter too, on the car i have de-cat pipe and cold air intake!! so if anyone could advise me on how it would run that would be great, thanks.
Reply With Quote
  #2 (permalink)  
Old 26 Nov 2007, 06:01 pm
Junior Member
 
Join Date: Nov 2007
Posts: 1
Default

It should run the same at idle. you will definatly need to get it remapped as its changing the fueling!I don't know the system but any uprating of the fueling needs to be reset to give the best performance.
Reply With Quote
  #3 (permalink)  
Old 26 Nov 2007, 06:16 pm
Junior Member
 
Join Date: Sep 2007
Posts: 10
Default

four times?
Reply With Quote
  #4 (permalink)  
Old 26 Nov 2007, 06:31 pm
Member
 
Join Date: Nov 2007
Posts: 35
Default

You need to get your ECU reflashed to match the new intake manifold and throttle body.
Reply With Quote
  #5 (permalink)  
Old 26 Nov 2007, 06:46 pm
Senior Member
 
Join Date: Aug 2007
Posts: 163
Default

first it's vtec not vti, vti is toyota. vtec is the first and the best variable valve and electronic lift control. Those are some good bolt ons, i would also suggest some higher lift cams you could leave the non vtec profiles the same but have a different grind on the vtec lobes for the sake of low rpm driveability. Doing some head work will vastly increase you performance with the modifications you stated. I would take it to a reputable tuner and dyno tune. Buy a hondata system (only 200-300 dollars) to do the tuning and to get the best horsepower out of your car. Without a hondata system which is cheap compared to a stand alone you won't get what you should be getting. You'll be able to adjust your a/f, timing, boost, nitrous, vtec changeover. a lot of other variables if you decide to go those routes for the vtec portion of the powerband and the non vtec portion of the powerband
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
honda civic vti 99 b16, looking for answers about after market inlet manifold and throttle kevy Acura Technical 6 26 Nov 2007 07:31 pm
thanks for your answers but not solved "the honda Civic pump oil.? Francisco T Honda Technical 1 04 Nov 2007 02:42 pm
Is the intake manifold the same thing as the exhaust manifold? cooloonka Honda Technical 5 03 Nov 2007 03:00 pm
what is the inlet size of the stock muffler on a 1998 honda civic dx?? boostboi Honda Technical 1 05 Oct 2007 10:16 am
Does anyone know when Honda Pilot HYBRID will be out in the market; in CALIFORNIA Market? Gult Honda Technical 1 28 Aug 2007 04:04 am


All times are GMT -5. The time now is 02:37 am.


Attribution:
Honda News | Autoblog
Powered by Yahoo Answers




Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
LinkBacks Enabled by vBSEO 3.6.0 PL2 © 2011, Crawlability, Inc.
HondaCarForum.com is not affiliated with Honda Motor Company in any way. Honda Motor Company does not sponsor, support, or endorse HondaCarForum.com in any way. Copyright/trademark/sales mark infringements are not intended or implied.