the easiest way is to let the dealer reset it with a pgm
"jim" <jim@noname.com> wrote in message news:40478CC0.4671@noname.com...
> Woody wrote:
> >
> > If you wait a while it will probably reset itself if there are no
faults.
> > Most reset after a few drive cycles...
> >
> > "self reg test 12" <cbwucvuwbu@cox.net> wrote in message
> > news:s9z1c.27902$qL1.21743@fed1read02...
> > > jim wrote:
> > > > self reg test 12 wrote:
> > > >>
> > > >> I removed the passenger seat to haul some long tables and after
> > > >> reinstalling and reconnecting all of the wiring, the SRS light
stays
> > > >> lit on the dash. Is there a reset switch or button?
> > > >>
> > > >> --
> > > >>
> > > >> Chris
> > > > hey check out this, found it on the www.yahoo.com and did a search
> > > > on SRS light, honda and came up with this... hope it helps... i have
> > > > the same problem with a 2001 civic and got alot of sites with info
on
> > > > how to reset it... the best one is on www.superhonda.com where it
> > > > shows you the pictures, i could not locat the thing under my dash,
> > > > kinda old and could not bend that far down to get under there(bad
> > > > back) oh well will get some kid to climb under there and check it
out
> > > > of me... http://www.honda-tech.com/zerothread?id=264288
> > >
> > > --
> > >
> > > Thanks, Jim. This looks like a winner. Pasting for others to use:
> > >
> > >
> > > Directions for erasing memory on SRS light
> > > 1st you need to either buy or make the "SCS Service Connector." I used
a
> > > speaker harness for and older Honda which you can buy at a local
stereo
> > shop
> > > such as Circuit City or Best Buy, and cut the wires and looped them
> > > together. You can also use a paperclip but that will make it a little
more
> > > difficult because you have to connect it and disconnect it a few times
> > > quickly.
> > > 2nd you need to find the MES (Memory Erase Signal) connector
> > >
> > > MES Plug in Fuse box. It is a yellow connector with two wires in it
that
> > is
> > > plugged into the fuse box, unplug it and pull it down. Once you have
done
> > > that you can begin the process of erasing the memory. NOTE: This will
only
> > > reset your SRS System if what caused it to trigger has been fixed, Ex:
> > > turning the ignition on with any SRS Plugs disconnected, such as
pulling
> > > your seat out.
> > >
> > > 1st step in erasing the memory is to turn the ignition off and connect
the
> > > SCS Service connector to the MES Plug,
> > >
> > > 2nd Turn Ignition on. SRS indicator light will come on for about 6
seconds
> > > then go off.
> > >
> > > 3rd Disconnect SCS service connector for MES connector within 4
seconds
> > > after SRS indicator light goes off. SRS indicator light will come on
> > again.
> > >
> > > 4th Reconnect SCS service connector the MES connector within 4 seconds
> > after
> > > SRS light comes on. SRS indicator light will go off.
> > >
> > > 5th Disconnect SCS service connector from MES connector within 4
seconds.
> > > SRS indicator light will indicate that memory is erased by blinking 2
> > times.
> > >
> > > 6th Turn ignition off, and wait 10 seconds. Start vehicle like normal
and
> > > light should come on and go out like normal. You have reset your SRS
> > light,
> > > congrats.
> > >
> > > If it does not work the first time try it again, the timing has to be
> > > perfect. My first time it took me 3 attempts before it worked, but it
did
> > > work.
> > >
> > >
> gee the info i received from the honda dealer and from the internet is
> that you have to reset it to get the light to go out... unless the bulb
> burns out....